CG03+ Problem

Discussion in 'Typhoon H Discussion' started by WTFDproject, Mar 23, 2020.

  1. WTFDproject

    WTFDproject Active Member
    Staff Member

    Oct 3, 2018
    846
    120
    43
    Male
    Retired Power Plant
    North Carolina Piedmont
    This Thread is created to assist @Harold MATHIEU. The text of this intial post is copied from a profile post requesting assistance:
    *************************************************************************************************************************

    Original:
    Après avoir démonté ma caméra cgo3+ pour une révision, j'ai un code erreur. 3 long bip et 2 bip court. Malheureuse je ne comprend rien.


    Translation:
    After taking my cgo3+ camera apart for servicing, I got an error code. Three long beeps and two short beeps. Unfortunately, I don't understand anything.
     
  2. WTFDproject

    WTFDproject Active Member
    Staff Member

    Oct 3, 2018
    846
    120
    43
    Male
    Retired Power Plant
    North Carolina Piedmont
    @Harold MATHIEU,
    Are you certain the code you hear is 3 long and 2 short? I am not familiar with that code.
    However, if the code is 2 long and 3 short, it would mean the Pitch (tilt) encoder has an issue. It may not be plugged in correctly, or it may be a broken wire.
    I am not sure if this picture will be helpful with no translation available, but it may provide some assistance.


    @Harold MATHIEU,
    Êtes-vous certain que le code que vous entendez est 3 long et 2 court ? Je ne connais pas ce code.
    Cependant, si le code est long (2) et court (3), cela signifie que le codeur de tangage (tilt) a un problème. Il se peut qu'il ne soit pas branché correctement ou que le fil soit cassé.
    Je ne suis pas sûr que cette image soit utile en l'absence de traduction, mais elle peut apporter une aide.

    cgo3+ Gimbal Board Connections5.jpg
     
  3. Harold MATHIEU

    Harold MATHIEU New Member

    Mar 23, 2020
    2
    0
    1
    Male
    Thank you for your answer.
    I'm sure of the beep.
    3 long followed by 2 short.
    The diagram that you showed me I also have it, and nothing appears there. I checked all the connections and no wires cut or badly laid. All worked very well. I just had the two little engines a bit blocked because of the sea salt. Is it possible that the position of the rotor of small motors is mandatory? Or that the evening card has been deprogrammed?
     
  4. WTFDproject

    WTFDproject Active Member
    Staff Member

    Oct 3, 2018
    846
    120
    43
    Male
    Retired Power Plant
    North Carolina Piedmont
    Traduit avec www.DeepL.com/Translator (version gratuite)
    Oui, les petits moteurs doivent être positionnés correctement.
    Mais la mention du sel de mer est probablement plus importante. Si l'appareil photo a été immergé dans de l'eau salée, les chances de récupération ne sont pas bonnes.
    J'espère que quelqu'un d'autre reconnaîtra le code de 3 long / 2 court. Mais je ne reconnais pas le code. Il peut être nécessaire de remplacer l'appareil photo, ou au moins d'en discuter avec un centre de service.

    Translation:
    Yes, the small motors must be positioned correctly.
    But the mention of sea salt is probably more important. If the camera has been immersed in salt water, the chances of recovery are not good.
    I hope someone else will recognize the code of 3 long / 2 short. But I don't recognize the code. It may be necessary to replace the camera, or at least discuss it with a service center.
     
  5. Harold MATHIEU

    Harold MATHIEU New Member

    Mar 23, 2020
    2
    0
    1
    Male
    It did not fall into the water. Just the spray. As I said before. Everything was working properly before disassembly.
     
Loading...

Share This Page