Rebinding problem

Discussion in 'General Discussion' started by s7ein, Jun 11, 2016.

  1. s7ein

    s7ein New Member

    Jun 10, 2016
    4
    0
    1
    How do you rebind the q500 with the transmitter?
     
  2. Stan Burcham

    Stan Burcham New Member

    Aug 7, 2015
    15
    3
    3
    Male
    Do you have the manual?
     
  3. droner

    droner Active Member

    Jan 21, 2016
    396
    80
    28
    Male
    McConnell, IL
    Turn on your G and rock it back and forth 5 times quickly so it thinks you crashed. You should see a blinking yellow light on your rear status indicator. Turn on the ST10 and go to the Flight Setting menu. Press Bind and select your model. If it binds right you should get the "happy tune".

    Don't forget you may have to bind your camera again too.

    hf!
     
  4. nrrtrains

    nrrtrains Well-Known Member

    Jul 27, 2015
    1,245
    262
    83
    Male
    Staten Island New York USA
    hi
    open pdf
    fly safe
     

    Attached Files:

  5. nrrtrains

    nrrtrains Well-Known Member

    Jul 27, 2015
    1,245
    262
    83
    Male
    Staten Island New York USA
    hi
    just in case you need to bind tour camera
     

    Attached Files:

  6. s7ein

    s7ein New Member

    Jun 10, 2016
    4
    0
    1
    I tried rebinding it and appreciate the help so far. After I get the light underneath or in bind mode, I go to model select I created a new one for the q500 as there wasn't one and when I go to flight setting and then to bind after that under model there is nothing. U see camera there is something and I connect to that but what if there isn't anything under model. How do I get this part to work?

    Thanks
     
  7. Rnlcomp

    Rnlcomp Active Member

    Nov 1, 2015
    296
    140
    43
    Male
    Auto tech
    New Orleans
    If you followed the instructions already posted then you either have a bad bird or a bad tx.
    .
     
  8. Davidnclearlaketx

    Davidnclearlaketx Active Member

    Dec 5, 2015
    996
    216
    43
    Male
    Texas/USA
    Not sure if you'd tried it yet but on one Yuneec YouTube video they said to delete the current/previous model stored in the ST10 and create another entry then bind it to the newly created Q500.
     
  9. Davidnclearlaketx

    Davidnclearlaketx Active Member

    Dec 5, 2015
    996
    216
    43
    Male
    Texas/USA
    Maybe take the battery out of the ST10 for a few minutes and do a factory reset before trying to rebind again if it still won't work.
    Call Yuneec's 24 x 7 emergency hotline.... just kidding.... 8 or 9 AM PST open support phone number.... and hold, and hold, and listen to music, hold, wait, put on speakerphone, eat breakfast, shave, ..... TV news....read. Drone360 magazine latest online issue...
    :-(
     
  10. nrrtrains

    nrrtrains Well-Known Member

    Jul 27, 2015
    1,245
    262
    83
    Male
    Staten Island New York USA
    hi
    do you know any one that has an ST-10 if so ask them if they will try to bind your Q with their ST-10 if that works your ST-10 is not working correctly , ( witch is probably the case ) .
    fly safe
     
  11. Glen Janota

    Glen Janota New Member

    Feb 26, 2019
    13
    1
    3
    Male
     
  12. Glen Janota

    Glen Janota New Member

    Feb 26, 2019
    13
    1
    3
    Male
     
  13. Glen Janota

    Glen Janota New Member

    Feb 26, 2019
    13
    1
    3
    Male
    I apologize for not finding the right thread but hopefully someone's out there that can answer this. I managed to put two models on controller G & Q. Can someone tell me the proper procedure in switching models back and forth
     
  14. WTFDproject

    WTFDproject Active Member
    Staff Member

    Oct 3, 2018
    561
    77
    28
    Male
    Retired Power Plant
    North Carolina Piedmont
    For switching back and forth between existing models that have already been bound to the controller:
    1. Select "Model Select" at the lower right of the ST-10+ screen
    2. Select "OK" on the "WARNING!!!" screen that comes up.
    3. Press the desired model on the "Model" select Screen.
    4. IF a "Model Selection" warning appears, Select "OK".
    5. Verify your selected model is indicated by a blue box around it.
    6. Press the return button at lower right to return to the main screen.
    7. Ensure the Q500 is turned on and has completed initialization.
    8. Verify the main screen populates with telemetry information.
    9. It is sometimes necessary to reselect / rebind the camera before video shows up,
     
  15. WTFDproject

    WTFDproject Active Member
    Staff Member

    Oct 3, 2018
    561
    77
    28
    Male
    Retired Power Plant
    North Carolina Piedmont
  16. Glen Janota

    Glen Janota New Member

    Feb 26, 2019
    13
    1
    3
    Male
    Thank you so much for your time. My main concern was do I need to after swapping did it need calibrating each and every time? So, long as I see the correct light underneath with an occasional White blink I'm good to go I hope is what you're saying
     
  17. WTFDproject

    WTFDproject Active Member
    Staff Member

    Oct 3, 2018
    561
    77
    28
    Male
    Retired Power Plant
    North Carolina Piedmont
  18. WTFDproject

    WTFDproject Active Member
    Staff Member

    Oct 3, 2018
    561
    77
    28
    Male
    Retired Power Plant
    North Carolina Piedmont
    [QUOTE="did it need calibrating each and every time? So, long as I see the correct light underneath with an occasional White blink I'm good to go I hope is what you're saying[/QUOTE]

    Once calibrated, you are good to go unless you have moved the drone more than about 100 miles from the place it was calibrated. So yes, generally you are good to go on both drones until some other event requires a new calibration.
     
    mk2112 likes this.
Loading...

Share This Page